+971 58 558 1295 ENTR Request a Quote
Steam room behind a frameless glass door, with dark stone walls, a floating stone bench lit from below and steam filling the room

[ Blog ]

Residential Steam Room Planning Guide: Size, Build-up, Steam

Planning a home steam room in 6 decisions: size and seats, location, wall and ceiling build-up, door and glass, generator and controls, order of works.

6 min read

Sauna Dekor Spa Solutions — designing, manufacturing and installing saunas, steam rooms, hammams and pools since 1987, in our own facility in İkitelli OSB, Istanbul.

TopicResidential Steam Room Planning Guide
Reading6 minutes
Sections9
Published4 November 2026
Updated

Sauna Dekor Spa Solutions engineering team, Istanbul · project and press enquiries: Alican Aykaç, Managing Partner

Updated: 11 November 2026

Short answer: plan a home steam room in 6 decisions: size and seats, location, wall and ceiling build-up, door and glass, generator and controls, and the order of works. A steam room runs at 40–50 °C at close to 100 % relative humidity, so every decision is about keeping that water inside the room. Sauna Dekor Spa Solutions draws all 6 on one coordinated drawing before any wall is built.

Steam room with a frameless glass front, a white solid-surface bench, a round stool, a hand shower and an LED strip along the bench
A home steam room behind a frameless glass front. Project photograph; project not named.

How big should a home steam room be?

Sized to the people who use it together, usually 2 to 4 in a home. A typical practice value is about 60 cm of bench length per seated person and a ceiling around 2.2–2.4 m before the slope. A larger room is not better: every extra cubic metre needs more steam and gives more surface to condense on.

Benches run along 1 or 2 walls, at seat height, with a slight fall towards the room. A lying bench needs the length of a person; plan it from the start if wanted.

Where should it go in the house?

Next to a bathroom or shower, on a floor that can take a drain, with a dry cupboard nearby for the generator. In 3 of 4 homes we plan, the steam room shares a wall with the master bathroom. Avoid outside walls that are cold in winter or hot in summer, and ceilings under a roof void that cannot be sealed.

What goes behind the tiles?

A waterproof build-up of 4 layers on every wall, the ceiling and the floor: a stable backing or board, a continuous membrane with taped joints, adhesive and tile. The membrane runs without a break over corners and the ceiling, and every penetration is sealed into it.

The usual penetrations are the steam outlet, the sensor, the lights and the drain. The detail is set out in our guide to the steam room vapor barrier.

What goes behind the tiles?
DecisionWhat it fixesWho needs it first
Size and seatsvolume, bench layout, ceiling heightarchitect
Locationdrain, generator cupboard, shower nearbyarchitect and MEP engineer
Build-upmembrane, board, tile, sealed penetrationssteam room builder
Door and glassseal, threshold, glass areasteam room builder
Generator and controlspower, water, drain, sensor and panelelectrician and plumber
Order of workssite programmemain contractor

Why must the ceiling slope?

So condensate runs to the walls instead of dripping on the bather. A slope of 2–5 degrees (typical practice value), or a vault, is enough; a flat ceiling drips in the first week. The ceiling is built from the same waterproof board as the walls.

Lights in the ceiling are sealed fittings rated for a hot, wet room. Typical layouts are shown in our page on steam room design.

Glass mosaic steam room with a vaulted ceiling, a recessed ceiling light and a lit mosaic bench along the wall
A vaulted steam room ceiling with a recessed light. Project photograph; project not named.

Which door and how much glass?

A tight glass door, usually frameless and 1 leaf wide, with a threshold falling into the room so water stays inside. A small gap or vent lets fresh air in during the session. Glass walls give light and space but add cold surface, which raises the generator size; the glass area is part of the sizing, not an afterthought.

How are the generator and controls placed?

The generator sits in a ventilated cupboard outside the room, close enough for a short steam line. The steam outlet goes low on 1 wall, away from the benches; the sensor goes on the opposite wall at the height the maker gives; the control panel sits outside the door or inside if rated for it. Our steam generator page shows how the generator is matched to the room.

In what order is a home steam room built?

In 6 steps: services first, then backing and membrane, then a water test, then tiles, then door and equipment, then commissioning with a full steam cycle. The water test before tiling is the step that decides whether the room leaks in year 3.

  1. Drain, water, power and steam line brought to the room and cupboard.
  2. Backing boards and membrane on walls, ceiling and floor.
  3. Flood test of the floor and inspection of every penetration.
  4. Tiles, bench finish and grout suited to hot, wet rooms.
  5. Glass door, steam outlet, sensor, lights and panel.
  6. Generator connected and the room run through a full cycle.
Glass mosaic steam room with curved two-level benches and a lit strip along the bench edge
A finished home steam room with tiled benches. Project photograph; project not named.

Choosing between a steam room and a sauna? Our comparison of a sauna vs steam room sets out heat, humidity and services. The steam rooms we build for homes and hotels are on our steam room page.

Sauna Dekor Spa Solutions is a sauna, steam room, hammam and pool manufacturer since 1987: 40 years of manufacturing in Istanbul (İkitelli OSB), a team of 19, TS EN ISO 9001:2015, and 5,000+ projects in 41+ countries, including 577+ hotel and resort projects, with 732 documented references in 32 countries and territories. Our warranty is 24 months on workmanship and manufacturing, 24 months manufacturer's warranty on electrical and mechanical equipment, and 5 years on structure and waterproofing. We do not manufacture the steam generator; its certification belongs to its maker. Our full range is on our products page.

Steam room or hammam at home: which one fits?

Short answer: a steam room needs less space and no heated platform; a hammam needs a heated marble platform and basins and takes 3–8 weeks to build in a home. Both keep the room air at 40–50 °C.

Steam room or hammam at home: which one fits?
Steam room Hammam
Room air 40–50 °C, close to 100 % humidity 40–50 °C
Heat source Generator outside the room Heated platform (40–45 °C) and steam
Finish Mosaic, tile or stone Marble or stone
Build time at home Depends on scope 3–8 weeks

Source: Sauna Dekor design values.

See how a hammam is built.

Updated:

What should a steam room specification include?

Short answer: a steam room is a wet, saturated room, so the specification has to cover the generator, the waterproofing and the shape of the ceiling, not only the finish.

  1. Design condition: 40–50 °C at close to 100 % relative humidity.
  2. Steam generator named by make and model, sized to room volume and finishes, installed outside the room with a service position.
  3. Continuous waterproofing and vapour barrier across walls, floor and ceiling, tested before tiling.
  4. Sloped ceiling so condensation runs to the walls, and a floor drain with falls.
  5. Steam-tight door, lighting and controls rated for a wet room, and the drain and water supply for the generator.

Send us your room drawing or see why the vapour barrier matters.

Updated:

For a home steam room built from a factory-made module, see wedi ModularSpa.

Frequently asked questions about home steam rooms

What temperature does a home steam room run at?


A steam room runs at 40–50 °C at close to 100 % relative humidity. The control panel holds the set point with the sensor on the wall opposite the steam outlet, and the generator adds steam as the room cools.

How do you make a steam room at home?

Build a sealed, waterproofed room with a sloped ceiling, a drain and a steam generator outside the room, sized to the room's volume and finishes. The room runs at 40–50 °C close to 100 % humidity, so the membrane and boards are tested before any tile goes on.

Can a steam room be built in an existing bathroom?


Often yes, if the bathroom can take a drain, a sealed ceiling and a nearby cupboard for the generator. A site visit checks the floor level, the ceiling void and the electrical supply first.

Does a home steam room need an extract fan?


Yes, a controlled extract that runs after the session to dry the room, not at full speed during it. A small fresh-air inlet near the door keeps the air comfortable while the room is in use.

Which tiles work in a steam room?


Porcelain and glass mosaic on a flexible, water-resistant adhesive with a grout suited to hot, wet rooms. Some natural stones need checking first, and every tile goes on a membrane that has passed a water test.

How long does it take to build?


In a home, the steam room is usually built over a few weeks, set by curing times for screed, adhesive and grout. The generator connection and the commissioning take a day or two at the end.

What maintenance does it need?


Wipe the benches after use, leave the door open to dry the room, and descale the generator at the interval its maker states. The sensor, outlet and drain are checked at the annual service.

Our work

Steam room projects

Alican Aykaç, Managing Partner, Sauna Dekor
[ Author ]

Alican Aykaç · Managing Partner, Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions has designed, manufactured and installed saunas, steam rooms, hammams and pools since 1987, in its own facility in İkitelli OSB, Istanbul: 5,000+ projects in 41+ countries, including 577+ hotel and resort projects.

About Alican Aykaç

[ Related applications ]

Planning a room like this?

Send us the drawing or the room size. We will work out the heater, ventilation and finishes the room needs.

Ready to learn more?

Book a consultation or speak with our team.

We’d love to cooperate
TO BUILD AMAZING POOLSAUNATURKISH BATH & HAMMAMSNOW ROOMSTEAM ROOMSALT ROOMWHIRLPOOL

Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions was established in 1987. In order to spread the use of Spa & Wellness, it introduced its products in many international fairs and followed the innovations abroad and examined the Spa & Wellness culture on-site, and made perfect applications with quality materials and correct manufacturing techniques.

Talk to our team

Dubai office · Istanbul factory

WhatsApp+90 532 215 64 78Call Dubai+971 58 558 1295Request a quote