+971 58 558 1295 ENTR Request a Quote
Two glass-fronted timber sauna cabins side by side on a wooden deck with rain shower

[ Project ]

Private Countryside House Sauna

Sauna Dekor Spa Solutions — designing, manufacturing and installing saunas, steam rooms, hammams and pools since 1987, in our own facility in İkitelli OSB, Istanbul.

A sauna built into a private countryside house — timber selection and grain, glazing, lighting design, ventilation and insulated cabin build-up.

  • Sauna

[ 12 photos ]

From the project

Sauna
Sauna
Sauna
Infrared sauna
Sauna
Sauna
Infrared sauna
Infrared sauna
Infrared sauna
Infrared sauna
Sauna

[ The build ]

01

Overview

Sauna Dekor is a Turkish sauna and hammam manufacturer that also acts as turnkey contractor for the wet areas it builds. Founded in 1987 and in its 40th year, the company produces in its own İkitelli, Istanbul facility and has delivered thermal installations in 41+ countries.

This project is a sauna built into a private countryside house. The owner is not named and the location is not published; the page records the property type and the work. The zone listed for theproject is a sauna, and our photographic record of the job runs to eleven frames.

02

Scope of work

A dry-heat cabin taken as a joinery-led commission: the insulated structure, linings,benching and back rests, glazing, integrated lighting, the heater and control, and the ventilation and electrical interfaces. Manufactured and dry-assembled in our Istanbul workshop,then dismantled, numbered, shipped and installed.

03

Timber selection is a comfort decision, not a finish decision

Everything a bather touches in a sauna is timber, at temperature, with bare skin. That makes species selection a comfort question first. We use kiln-dried, low-resin species because resinweeps at bench temperature and because a dense, oily timber conducts heat into skin far faster than a light, open one — which is why an otherwise well-built cabin can be uncomfortable to sitin. Boards are selected and laid so the visible grain runs consistently, knots are kept away from contact surfaces, and every fixing is concealed so no metal is presented to skin. Benchtops are built to lift out, both for cleaning and because a bench is the part most likely to be replaced in the cabin’s life. Seesauna.

04

Light and glazing

Lighting in a sauna is a heat and safety question before it is an atmosphere one. Fittings have to be rated for the temperature and humidity they will sit in, positioned where nobodybrushes them, and wired so the cabin’s vapour barrier is not perforated by cable routes.Indirect light behind a bench or a back rest gives the effect most clients want while keeping the fitting away from contact and away from the hottest part of the room. Glazing is specified as a sauna component — toughened, correctly gasketed, with a door that seals without binding asthe frame warms — and its heat loss is added to the heater calculation rather than ignored.

05

Heat load, build-up and ventilation

General practice sizes a domestic cabin at roughly a kilowatt of stone-heater output percubic metre of volume, with additions for glazing and for masonry surfaces. The cabin is an insulated box: insulation, a continuous foil vapour barrier with taped laps, a ventilated cavity, then the lining, so each board can dry from the back. Air enters low near or under theheater and leaves low on the opposite side, ducted somewhere that can accept warm moist air.Connection is made by a local electrician to the national wiring rules; the heater carries CEand EN 60335 certification from its manufacturer. More atsauna ventilation.

06

What we solved on site

A joinery-led cabin has to be right the first time, because a panel re-cut on site nevermatches the grain sequence it was selected for. We laid the boards out and dry-assembled the entire cabin in our Istanbul workshop, confirmed the grain ran as intended across every junction, then dismantled and numbered it so it wentback together the same way. Seesauna designs for luxury homes and luxury home sauna.

07

Frequently asked questions

Why does sauna timber have to be low in resin?

Because resin weeps at bench temperature. Species selection is also a comfort decision: a dense, oily timber conducts heat into bare skin far faster than a light, open one, which makes a well-built cabin unpleasant to sit in.

How should a sauna be lit?

With fittings rated for the temperature and humidity, positioned where nobody brushes them, and wired without perforating the vapour barrier. Indirect light behind a bench or back rest gives the effect while keeping the fitting out of contact.

Is sauna glazing ordinary glass?

No. It is a sauna component — toughened, correctly gasketed, with a door that seals without binding as the frame warms — and its heat loss is added to the heater calculation rather than ignored.

Why dry-assemble the whole cabin before shipping?

Because a panel re-cut on site never matches the grain sequence it was selected for. Assembling and numbering in the workshop means the cabin goes back together exactly as it was laid out.

Sauna Dekor’s own certification is TS EN ISO 9001:2015 quality management, covering sauna and spa product manufacturing and after-sales service. The equipment we install carries CE / EN 60335, TÜV, GS, GREENGUARD Gold, FSC and VDI 6022 certification from its own manufacturers — EOS, Sentiotec and Condair among them.

Portfolio

Similar projects: same rooms, country or type of building

Have a similar project?

Send us your plan; we will work out the scope and the rooms it needs.

Last updated:

[ Related pages ]

Ready to learn more?

Book a consultation or speak with our team.

We’d love to cooperate
TO BUILD AMAZING POOLSAUNATURKISH BATH & HAMMAMSNOW ROOMSTEAM ROOMSALT ROOMWHIRLPOOL

Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions was established in 1987. In order to spread the use of Spa & Wellness, it introduced its products in many international fairs and followed the innovations abroad and examined the Spa & Wellness culture on-site, and made perfect applications with quality materials and correct manufacturing techniques.

Talk to our team

Dubai office · Istanbul factory

WhatsApp+90 532 215 64 78Call Dubai+971 58 558 1295Request a quote