+971 58 558 1295 ENTR Request a Quote
Lusail villa Finnish sauna with LED-lit benches, a glass front and a corner heater

[ Project ]

Lusail Villa — Finnish Sauna

Doha · Qatar

Sauna Dekor Spa Solutions — designing, manufacturing and installing saunas, steam rooms, hammams and pools since 1987, in our own facility in İkitelli OSB, Istanbul.

A private villa Finnish sauna delivered in Lusail, Doha, Qatar in 2025 — glass front, LED-lit benches, stone heater. Sauna Dekor, manufacturer since 1987.

  • Sauna

Project summary

What we delivered

  • Rooms: Sauna
  • Where and when: Doha · Qatar, 2025
  • In short: A private villa Finnish sauna delivered in Lusail, Doha, Qatar in 2025 — glass front, LED-lit benches, stone heater. Sauna Dekor, manufacturer since 1987.

[ 5 photos ]

From the project

Sauna
Sauna
Sauna
Sauna

[ The build ]

01

A private Finnish sauna in Lusail, Doha

Sauna Dekor designs, manufactures and installs saunas, hammams and spa rooms as a single turnkey package. We have done it since 1987 — this is our 40th year — and we have delivered in 41+ countries. This project is a private villa in Lusail, Doha, Qatar, where we built a custom Finnish sauna with a full glass front, completed in 2025.

02

What was built

A single dry-heat cabin: wraparound tiered benches with backrests, concealed LED lighting run along the bench edges, a slatted guard around a floor-standing stone heater, a glazed front wall and door, and a digital control panel mounted outside the cabin next to the entrance. It is a one-room installation rather than a multi-room suite — the villa’s thermal programme here is the sauna alone.

03

The technical decisions behind it

Sizing a glass-fronted cabin

A glass front is the single most common reason a villa sauna underperforms. Our sizing rule is about 1 kW of heater output per cubic metre of insulated volume, plus roughly 1 kW per square metre of glazing. Glass has almost no thermal storage; it takes heat from the room and gives it straight back to the space outside, so the heater spends its life fighting a cold surface instead of holding a stable bench temperature. Getting that addition right is what separates a glass cabin that feels even from one that has a permanent cold edge near the door.

Glass detailing

The front is toughened safety glass on frameless hinges, set into a timber jamb with a compression seal. The glass is deliberately not tight to the floor: the small gap at the threshold is part of the ventilation path, not a tolerance error.

04

Ventilation

Supply low behind or beside the heater, extract low on the opposite wall, sized for roughly three to six air changes an hour in use. The cabin also runs a drying cycle after the session. Doha’s outdoor humidity is high for much of the year, which makes the post-session dry-down more important here than it is in a dry inland climate — a cabin that is never allowed to dry out will show it in the bench timber within a couple of seasons.

Heater and controls

A floor-standing stone heater with a slatted timber guard. The guard is not decoration; it fixes the clearance between bathers and the heater body, and it has to be dimensioned to the heater manufacturer’s own clearance table rather than to the joinery drawing. Control is external and digital, with a temperature limiter and a door contact, so the cabin can be brought up to temperature without opening it.

05

Lighting

LED is used as an indirect line under the bench noses and behind the backrest, with drivers outside the hot envelope. Fittings inside a sauna have to be rated for the cabin’s continuous operating temperature; the usual failure is not the LED itself but a driver quietly cooking inside the wall build-up.

Timber

Kiln-dried, low-resin species for linings and benches, fixed from below so no metal touches a seating surface. Cladding floats on battens with a vapour-tight layer and a ventilated cavity behind it, so the wall can dry in both directions.

06

What the site required

Villa thermal rooms in Doha are almost always retrofits into a completed house, and the constraint is nearly always the slab-to-slab height. Once the cabin ceiling, the ventilation path and the heater’s clearance zone are stacked up, the residual void is small, and the extract route has to be resolved inside it rather than by dropping the ceiling further. We prefabricate and dry-assemble the cabin in our Istanbul workshop, verify it against the surveyed opening, then number, dismantle and ship it, so the on-site phase inside a finished villa is assembly rather than fabrication.

07

Related capability

Room types and equipment are described on our sauna page, with the wet-heat counterparts under steam room and hammam. For cold-side pairing see cold plunge pools, and for how we work in Qatar see Doha.

08

Frequently asked questions

Does Sauna Dekor deliver private saunas in Qatar?

Yes. This Finnish sauna in a private villa in Lusail, Doha was completed in 2025. We manufacture in Istanbul and install in Qatar with our own supervision team; our Doha page describes how projects there are run.

Does a glass front make a sauna harder to heat?

It adds load, and it has to be paid for at the sizing stage. We add roughly one kilowatt of heater output for every square metre of glass, because glass re-radiates heat instead of holding it. Ignore that and the cabin will reach temperature but never feel stable.

Can LED lighting be used inside a Finnish sauna?

Yes, if the drivers sit outside the hot zone and the fittings are rated for the cabin’s operating temperature. In this cabin the light is run as a concealed line along the bench edges rather than as a downlight, which keeps the source out of the bather’s eye line and the driver out of the heat.

How long does a private sauna take from order to handover?

For a single villa cabin the governing items are usually the timber, the heater and the glass, plus shipping. We quote the programme per project against the drawing set rather than from a standard lead time.

Our own company certification is TS EN ISO 9001:2015 quality management, issued against a scope of sauna and spa product manufacturing and after-sales service. The equipment we install — heaters, steam generators, controls — carries its own CE / EN 60335, TÜV, GS and comparable approvals from its manufacturers, such as EOS, Sentiotec and Condair. We do not present those supplier approvals as our own.

Related pages

See how we design and build a Finnish sauna.

Portfolio

Similar projects: same rooms, country or type of building

Have a similar project?

Send us your plan; we will work out the scope and the rooms it needs.

Last updated:

[ Related pages ]

Ready to learn more?

Book a consultation or speak with our team.

We’d love to cooperate
TO BUILD AMAZING POOLSAUNATURKISH BATH & HAMMAMSNOW ROOMSTEAM ROOMSALT ROOMWHIRLPOOL

Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions was established in 1987. In order to spread the use of Spa & Wellness, it introduced its products in many international fairs and followed the innovations abroad and examined the Spa & Wellness culture on-site, and made perfect applications with quality materials and correct manufacturing techniques.

Talk to our team

Dubai office · Istanbul factory

WhatsApp+971 58 558 1295Call Dubai+971 58 558 1295Request a quote