+971 58 558 1295 ENTR Request a Quote
Glass front of a villa sauna with a glowing salt wall, a stone heater and lit timber benches inside

[ Blog ]

Infrared Cabin Planning Guide: Seats, Place, Power, Air

Planning an infrared cabin in 6 decisions: seats and emitters, where it stands, cabin or hybrid, circuit, room air and joinery, then the order of works.

Sauna Dekor Spa Solutions — designing, manufacturing and installing saunas, steam rooms, hammams and pools since 1987, in our own facility in İkitelli OSB, Istanbul.

TopicInfrared Cabin Planning Guide
Reading6 minutes
Sections8
Published18 November 2026
Updated

Sauna Dekor Spa Solutions engineering team, Istanbul · project and press enquiries: Alican Aykaç, Managing Partner

Updated: 18 November 2026

Short answer: plan an infrared cabin in 6 decisions: how many people sit in it and which emitters face each seat, where it stands, a stand-alone cabin or infrared panels added to a Finnish sauna, the electrical circuit, the room air and joinery around it, and the order of works. Sauna Dekor Spa Solutions supplies infrared cabins for villas, apartments and hotel spas, and most problems we are asked to fix start with the position, not the cabin.

An infrared cabin warms the people inside mainly by radiation from emitter panels, with the cabin air at about 45–60 °C. How that differs from a traditional sauna is explained in what is an infrared sauna.

Timber hybrid cabin with a backlit salt brick wall beside a stone heater in a timber guard, a long bench with a light strip and a wall lamp
A hybrid cabin in a private villa in Dubai: a stone heater and infrared emitters in one room, each on its own control. Project photograph; private client, not named.

How many seats, and which emitters face them?

Start with the number of people who sit at once, usually 1 to 4 in a home. Each seat needs emitters behind the back and, on most models, panels at the legs or under the bench. A bench longer than the emitter layout leaves 1 person facing bare timber, so the layout is drawn from the seats, not from the outside size.

Where should the cabin stand?

In a dry, ventilated room with free floor for the door to open and the gaps the cabin maker asks for at the sides, back and top. Avoid 3 places: a closed joinery niche, the wet zone of a bathroom and a corner in afternoon sun behind a large window. A dressing room or a room next to the bathroom often works; see our note on a bathroom sauna for the wet-zone side.

Where should the cabin stand?
DecisionWhat it fixesWho needs it first
Seats and emitterscabin size, emitter layout, powerowner
Positionclearances, door swing, sun, wet zonesarchitect or interior designer
Cabin or hybridwhether a heater and stones are addedowner, with us
Circuitboard capacity, protection, isolatorelectrician
Room air and joineryvents, gaps, service accessjoiner and MEP engineer
Order of worksdelivery, installation, handoversite manager

Stand-alone cabin or a hybrid sauna?

There are 2 common routes. A stand-alone infrared cabin is quick to place and needs only a circuit. A hybrid adds infrared panels to a Finnish sauna, so one room offers both; the Finnish side runs at 80–100 °C and needs the full sauna build-up, a heater and its air routes. Choose the hybrid only if both will really be used.

Glass-fronted timber cabin with a full-height glass door and long handle, a heater in a timber guard inside, an L-shaped bench with light strips and a small ceiling vent
A glass-fronted timber cabin: the glass and the door swing go on the plan from the first issue.

What electrical supply does it need?

A dedicated circuit from the board with its own residual-current protection, sized by a licensed electrician from the cabin maker's data, plus 1 isolator a technician can reach. Small cabins may run from a single phase; larger cabins and hybrids may need more. The details are in our guide to sauna electrical requirements.

Power units for the emitters sit behind a removable panel, never behind fixed boards. We keep spare parts in stock in Istanbul for the equipment we install, so a repair waits for access, not for parts.

What about room air and joinery?

The cabin gives off heat into the room during and after each session, so the room needs ventilation or air-conditioning, and the cabin's own vents stay open. Built-in joinery keeps a gap around the cabin with vents at 2 levels, top and bottom. Air-conditioning grilles should not blow onto the glass. Our page on sauna ventilation covers the hybrid case.

Timber cabin seen through its glass front, with warm light strips along the benches
A glass-fronted villa cabin. We place the control unit on the outside wall beside the door, within reach and away from water. Project photograph; private client, not named.

In what order is an infrared cabin installed?

In 5 steps: circuit and isolator first, then floor checked level, then delivery of the panels, then assembly, then commissioning with the owner. A standard cabin is installed in about 1 day once the circuit is ready; larger models take up to 2–3 days. Joinery around a built-in cabin is fitted after the cabin, not before.

  1. Circuit, protection and isolator installed and tested by the electrician.
  2. Floor checked level; delivery route measured from the front door to the room.
  3. Panels delivered and assembled; emitters and controls connected.
  4. Joinery fitted around the cabin with its gaps and vents.
  5. Commissioning: timer, set point and lock set with the owner present.

For a cabin that is one part of a larger home spa, see our page on a home spa in Dubai. The cabin types we supply are on our infrared sauna page.

Sauna Dekor Spa Solutions is a sauna, steam room, hammam and pool manufacturer since 1987: 40 years of manufacturing in Istanbul, a team of 19, TS EN ISO 9001:2015, and 5,000+ projects in 41+ countries, including 577+ hotel and resort projects, with 732 documented references in 32 countries and territories. Every project carries 24 months on workmanship and manufacturing, 24 months manufacturer's warranty on electrical and mechanical equipment, and 5 years on structure and waterproofing. Emitters and controllers are made by their manufacturers, whose certification belongs to them. Our full range is on our products page.

Frequently asked questions about infrared cabins

How hot does an infrared cabin get?


The cabin air is usually about 45–60 °C, lower than a Finnish sauna. Most of the warmth people feel comes from the emitter panels facing them, which is why their layout matters more than the air temperature.

Can an infrared cabin go in an apartment?


Usually yes, with the building's approval for the electrical connection. It needs no water supply or drain, but it does need a dedicated circuit, a dry room and free space around the cabin for air.

Can it be installed in a bathroom?


Only outside the wet zone and with the electrician's approval for that location. A dry room next to the bathroom is the safer choice, with the shower a few steps away rather than beside the cabin.

How long does installation take?


About 1 day for a standard cabin once the circuit is ready, and up to 2–3 days for larger models. Built-in joinery around the cabin is fitted afterwards and can add time.

Can infrared panels be added to an existing sauna?


Often, if the sauna has room on the backrest wall and the supply can carry the extra load. We check the bench layout, the controller and the board before confirming a hybrid conversion.

What maintenance does a cabin need?


Very little: wipe the benches and panels with a dry or slightly damp cloth, keep the vents clear, and check the door and connections once a year. Do not cover the emitters with towels during use.

Our work

Infrared in our projects

Alican Aykaç, Managing Partner, Sauna Dekor
[ Author ]

Alican Aykaç · Managing Partner, Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions has designed, manufactured and installed saunas, steam rooms, hammams and pools since 1987, in its own facility in İkitelli OSB, Istanbul: 5,000+ projects in 41+ countries, including 577+ hotel and resort projects.

About Alican Aykaç

[ Related applications ]

Planning a room like this?

Send us the drawing or the room size. We will work out the heater, ventilation and finishes the room needs.

Ready to learn more?

Book a consultation or speak with our team.

We’d love to cooperate
TO BUILD AMAZING POOLSAUNATURKISH BATH & HAMMAMSNOW ROOMSTEAM ROOMSALT ROOMWHIRLPOOL

Sauna Dekor Spa Solutions

Sauna Dekor Spa Solutions was established in 1987. In order to spread the use of Spa & Wellness, it introduced its products in many international fairs and followed the innovations abroad and examined the Spa & Wellness culture on-site, and made perfect applications with quality materials and correct manufacturing techniques.

Talk to our team

Dubai office · Istanbul factory

WhatsApp+90 532 215 64 78Call Dubai+971 58 558 1295Request a quote