Photo: EOS Saunatechnik

EOS PEB 10 — control unit

EOS · EOS Sauna and Steam Room Controls

Short answer: EOS PEB 10 is a sauna control unit made by EOS Saunatechnik in Germany. Sauna Dekor sizes, supplies and installs it in the saunas and steam rooms we build; the product and its certificates are the manufacturer's.

Power extension box, for loads the control unit cannot drive directly.

Category: Control units
Series: Standard series
Manufacturer: EOS Saunatechnik · Germany
Capacity: Selected by cabin volume

Request a quote

EOS Sauna and Steam Room Controls

Model note

What the EOS PEB 10 is

The PEB 10 is a relay box that takes over the load the control unit cannot switch directly: it adds 10 kW of switching capacity. With a 9 kW (or 10 kW) control unit it takes dual-circuit heaters up to 19 kW (or 20 kW); with 18 kW control units up to 28 kW — HD type heaters are the exception. The housing uses the same case as the Compact range, 220 × 255 × 65 mm, in anthracite, and mounts on the wall. Connections are made from below or from the rear, and it runs quietly. Supply is 400 V three phase. The manufacturer states on each product page which heater needs one; we calculate that at quotation stage and allow space for it in the panel.

Close alternatives we also supply and install: the EOS U-Command (Control units), the EOS EmoTouch 3 (Control units), the EOS EmoStyle Hi (Control units). It belongs to the EOS Sauna and Steam Room Controls. The EOS overview lists every range.

Technical specifications

EOS PEB 10 specifications

Category	Control units
Series	Standard series
Manufacturer	EOS Saunatechnik · Germany
Capacity	Selected by cabin volume
Electrical connection	400 V 3N ~ 50 Hz
Switching capacity	10.0 kW
Dimensions HWD	220 x 255 x 65 mm

Values: EOS Saunatechnik's published product information (read 15 September 2026). Figures not listed here are sent with the manufacturer's technical sheet.

Selection

How we find the right capacity

We work out the capacity from the cabin volume; the five steps below are done together at the quotation stage.

Start with the cabin volume

Basic rule: cabin volume (m³) × 1 kW. A 2 × 2 × 2.10 m cabin is 8.4 m³ and needs about 9 kW. This figure is a starting point, not the answer.

Add glass and uninsulated surfaces

Add 1.2 m³ to the volume for every m² of glass front, and about 1.2 m³ for every m² of uninsulated concrete or stone. In a cabin with a full glass front, the real requirement is thirty to forty percent above the bare volume.

Agree the power supply early

Above 9 kW a 400 V three-phase supply is required; for lower outputs the phase is chosen according to the heater's installation manual. The heater is fed on its own circuit, with its own fuse and residual current device.

State the usage intensity

A home cabin used two hours a day and a hotel cabin open for ten hours cannot use the same unit. For commercial use, heavy-duty (HD) units and a larger stone mass are chosen.

Choose the control together with the heater

The power a control unit can switch directly is limited; above that, a PEB power boost unit is needed. This is calculated at the quotation stage.

Why EOS

Five series, one ecosystem

The logic you set up in a home works in a hotel too.

Five series, one control family

The same control family runs from the Standard series up to the large commercial series. The logic you set up in a home works in a hotel too.

Modular control

Sauna, hammam, steam and infrared modules plug into the EmoTouch 3 unit. Four rooms are run from one panel, with no separate switchboard.

Open to building automation

With the KNX and Modbus module it connects to the hotel management system, and opening hours can be programmed centrally.

Safety as a separate line

Door contact, emergency button, heater guard and EOSafe are available as separate products. In a commercial facility they are not optional.

Spare parts stock

We keep spare parts in stock in Istanbul for the equipment we install. In a commercial facility, what keeps a cabin closed for months is waiting for parts.

Around 20 years with EOS

We have been installing EOS equipment for around 20 years, so we know from site work how each unit performs in each room volume.

Frequently asked questions

Who manufactures the EOS PEB 10?

EOS Saunatechnik, in Germany. Sauna Dekor sizes, supplies and installs it; the product warranty and certificates are the manufacturer's.

Does Sauna Dekor install the EOS PEB 10?

Yes. We size, supply and install the EOS PEB 10 as part of the saunas and steam rooms we design, manufacture and build, in the Gulf and our other markets.

What are the main specifications of the EOS PEB 10?

Category: Control units; Series: Standard series; Manufacturer: EOS Saunatechnik · Germany; Capacity: Selected by cabin volume. Values are from the manufacturer's published product information.

Sources