EOS EmoStyle control unit, manufacturer product photo, manufacturer product image 1

EOS EmoStyle control unit, manufacturer product photo, manufacturer product image 2

EOS EmoStyle control unit, manufacturer product photo, manufacturer product image 3

Photo: EOS Saunatechnik

EOS EmoStyle — control unit

EOS · EOS Sauna and Steam Room Controls

Short answer: EOS EmoStyle is a sauna control unit made by EOS Saunatechnik in Germany. Sauna Dekor sizes, supplies and installs it in the saunas and steam rooms we build; the product and its certificates are the manufacturer's.

Control unit with a glass surface; for sauna cabins.

Category: Control units
Series: Classic series
Manufacturer: EOS Saunatechnik · Germany
Capacity: Selected by cabin volume

Request a quote

EOS Sauna and Steam Room Controls

Model note

What the EOS EmoStyle is

EmoStyle consists of a slim panel with a glass front and a separate power unit; the panel measures 132 × 135 × 25 mm and can sit up to 100 m from the sauna. It works with capacitive buttons, and the menu covers 19 languages. The D version is for dry sauna, the H version adds humidity control: humidity is delivered either time-proportionally in ten steps or as relative humidity with an optional sensor, with a 3 kW evaporator output. Dry-run detection is included. A drying programme runs after a humid session; temperature, fan speed and duration are each set separately. The Smart-Heat function stops steam production starting before the cabin has warmed up. It switches 10 kW directly and extends with PEB above that. The Cloud version connects to the cloud over Wi-Fi.

Close alternatives we also supply and install: the EOS Compact D18 / H18 (Control units), the EOS Compact DC / HC (Control units), the EOS Econ 4 (Control units). It belongs to the EOS Sauna and Steam Room Controls. The EOS overview lists every range.

Technical specifications

EOS EmoStyle specifications

Category	Control units
Series	Classic series
Manufacturer	EOS Saunatechnik · Germany
Capacity	Selected by cabin volume
Electrical connection	400 V 3N ~ 50/60 Hz
Power output	10.0 kW (can be expanded with PEB: PEB 10 / PEB 18 / PEB 36)
Temperature control range	30° – 115°C (Finnish) 30° – 70° C (Combi)
Heating time limitation	6 h, 12 h, unlimited
Start time pre-selection	24 h real time or week timer
Cabin light output	230 V, ohmic, capacitive, inductive load.
Fan output	230 V / max. 150 W, adjustable
Sensor system	Digital, inc. 5 m cable. Bench sensor optional.
Control panel (H/W/D)	132 x 135 x 25 mm installation assembly (mounting – optional)
Relay box (H/W/D)	270 x 300 x 100 mm wall mounting

Values: EOS Saunatechnik's published product information (read 15 September 2026). Figures not listed here are sent with the manufacturer's technical sheet.

Selection

How we find the right capacity

We work out the capacity from the cabin volume; the five steps below are done together at the quotation stage.

Start with the cabin volume

Basic rule: cabin volume (m³) × 1 kW. A 2 × 2 × 2.10 m cabin is 8.4 m³ and needs about 9 kW. This figure is a starting point, not the answer.

Add glass and uninsulated surfaces

Add 1.2 m³ to the volume for every m² of glass front, and about 1.2 m³ for every m² of uninsulated concrete or stone. In a cabin with a full glass front, the real requirement is thirty to forty percent above the bare volume.

Agree the power supply early

Above 9 kW a 400 V three-phase supply is required; for lower outputs the phase is chosen according to the heater's installation manual. The heater is fed on its own circuit, with its own fuse and residual current device.

State the usage intensity

A home cabin used two hours a day and a hotel cabin open for ten hours cannot use the same unit. For commercial use, heavy-duty (HD) units and a larger stone mass are chosen.

Choose the control together with the heater

The power a control unit can switch directly is limited; above that, a PEB power boost unit is needed. This is calculated at the quotation stage.

Why EOS

Five series, one ecosystem

The logic you set up in a home works in a hotel too.

Five series, one control family

The same control family runs from the Standard series up to the large commercial series. The logic you set up in a home works in a hotel too.

Modular control

Sauna, hammam, steam and infrared modules plug into the EmoTouch 3 unit. Four rooms are run from one panel, with no separate switchboard.

Open to building automation

With the KNX and Modbus module it connects to the hotel management system, and opening hours can be programmed centrally.

Safety as a separate line

Door contact, emergency button, heater guard and EOSafe are available as separate products. In a commercial facility they are not optional.

Spare parts stock

We keep spare parts in stock in Istanbul for the equipment we install. In a commercial facility, what keeps a cabin closed for months is waiting for parts.

Around 20 years with EOS

We have been installing EOS equipment for around 20 years, so we know from site work how each unit performs in each room volume.

Frequently asked questions

Who manufactures the EOS EmoStyle?

EOS Saunatechnik, in Germany. Sauna Dekor sizes, supplies and installs it; the product warranty and certificates are the manufacturer's.

Does Sauna Dekor install the EOS EmoStyle?

Yes. We size, supply and install the EOS EmoStyle as part of the saunas and steam rooms we design, manufacture and build, in the Gulf and our other markets.

What are the main specifications of the EOS EmoStyle?

Category: Control units; Series: Classic series; Manufacturer: EOS Saunatechnik · Germany; Capacity: Selected by cabin volume. Values are from the manufacturer's published product information.

Sources